This 12.8V 100Ah Group 24 LiFePO4 battery stores 1,280Wh of deep-cycle energy in a compact Group 24 case for RVs, camper vans, marine house-power systems, solar storage and off-grid applications. Built-in Bluetooth monitoring lets owners and installers check battery status from a compatible mobile device without opening the battery compartment or adding a separate display.
A 100A Smart BMS monitors charging, discharging, cell voltage and temperature, while low-temperature protection helps prevent unsafe charging below the permitted range. The Group 24 footprint also makes this model a practical option for selected AGM and lead-acid replacement projects, provided the battery compartment, charger, inverter, cable size, fuse protection and terminal clearance are verified before installation.
12.8V | 100Ah | 1,280Wh | Group 24 | Bluetooth Monitoring | 100A Smart BMS | Low-Temperature Protection | IP65
12V 100Ah Group 24 LiFePO4 battery with Bluetooth monitoring, 100A Smart BMS and low-temperature protection.
12V 100Ah Group 24 LiFePO4 Battery Highlights
Group 24 lithium battery: Compact dimensions support selected Group 24 AGM and lead-acid battery replacement projects.
Bluetooth monitoring: Check state of charge, voltage, current, power, temperature and operating status from a compatible mobile device.
100A Smart BMS: Monitors electrical conditions, cell voltage and battery temperature during charging and discharging.
Low-temperature protection: Automatically pauses charging when the cells are below the programmed safe charging range.
1,280Wh deep-cycle energy: Provides house power for compatible RV, marine, solar and off-grid systems.
1,280W continuous output: Supports compatible 12V loads and inverter systems within the BMS rating.
Expandable battery bank: Supports approved series and parallel configurations within the limits of the product manual.
IP65 enclosure: Helps protect internal components from dust and water spray when the battery is installed correctly.
Group 24 LiFePO4 Battery Size and Dimensions
Measuring approximately 10.24 × 6.61 × 8.27 inches, the battery follows the familiar Group 24 format used in many RVs, travel trailers, camper vans, boats and compact off-grid systems.
Before ordering, measure the battery compartment and confirm terminal clearance, mounting space and cable routing. Group size describes a general case format, but installation requirements can vary between vehicles and equipment.
Case format: Group 24
Dimensions: Approximately 10.24 × 6.61 × 8.27 in
Metric dimensions: Approximately 260 × 168 × 210 mm
Group 24 LiFePO4 battery dimensions: approximately 10.24 × 6.61 × 8.27 in / 260 × 168 × 210 mm with M8 terminals.
Bluetooth Monitoring for 12V LiFePO4 Battery
Bluetooth monitoring provides quick access to battery information without removing compartment covers or installing a separate display. It is useful during installation, routine inspection and system troubleshooting.
Available battery information may include:
Battery state of charge
Total battery voltage
Charge and discharge current
Input or output power
Remaining capacity
Battery temperature
Cycle count
Charging, discharging or standby status
Warning and protection status
Displayed information and available control functions depend on the confirmed BMS, mobile application and firmware version.
Bluetooth monitoring provides quick access to state of charge, voltage, current, temperature and battery operating status.
Low-Temperature Charging Protection
The Smart BMS monitors cell temperature and automatically pauses charging when the battery is below its permitted charging range. Charging becomes available again after the cells return to a safe temperature.
Automatic charge cut-off: Below 0°C / 32°F
Automatic charge recovery: At or above 5°C / 41°F
Automatic discharge cut-off: Below −20°C / −4°F
Charging temperature: 0°C to 50°C / 32°F to 122°F
Discharging temperature: −20°C to 60°C / −4°F to 140°F
Storage temperature: −10°C to 50°C / 14°F to 122°F
This model does not include self-heating.
Low-temperature protection pauses charging but does not warm the cells. For regular charging below freezing, install the battery in a temperature-controlled compartment or select a confirmed self-heating model.
100A Smart BMS and 1,280W Continuous Output
The integrated 100A Smart Battery Management System monitors voltage, current and temperature during charging and discharging. It disconnects the battery when operating conditions exceed the programmed limits and supports automatic recovery for compatible protection events.
Overcharge protection
Over-discharge protection
Charge and discharge overcurrent protection
Short-circuit protection
High-temperature protection
Low-temperature charging protection
Low-temperature discharge protection
Cell-voltage monitoring
Cell balancing
The battery supports up to 100A continuous charge and 100A continuous discharge, delivering approximately 1,280W of continuous output at nominal voltage. The recommended charging current is 20A for normal charging.
Group 24 Lead-Acid and AGM Battery Replacement
The Group 24 enclosure makes this battery suitable for selected AGM and lead-acid replacement projects. Before installation, confirm that the existing battery compartment, charging equipment and DC electrical system are compatible with LiFePO4 chemistry.
Check the following before replacing an existing battery:
Nominal system voltage
Battery-compartment dimensions
Terminal position and M8 connection requirements
Charger and inverter compatibility
Required continuous and surge current
Main fuse and cable ratings
Alternator charging configuration
Required operating temperature
Converting from lead-acid to LiFePO4 may require a lithium-compatible charger, revised inverter settings or a suitable DC-to-DC charger for alternator charging.
For a complete conversion checklist, charger guidance, DC-to-DC charging, wiring, fuse sizing and battery-group selection, read our
Lead-Acid to LiFePO4 Replacement Guide
.
12V Group 24 LiFePO4 Battery for RV, Marine and Off-Grid Power
This 12V lithium deep-cycle battery is designed for systems that require regular charging and discharging. Its compact Group 24 case and Bluetooth monitoring make it suitable for mobile and space-conscious power installations.
This is a deep-cycle energy-storage battery. Do not use it as an automotive or marine engine-starting battery.
Build a Larger LiFePO4 Battery Bank
Compatible batteries may be connected in series or parallel only when the ordered BMS configuration and controlled product manual expressly allow it. Approved limits can vary by production configuration, so the battery-bank design must be confirmed before ordering.
Series connection: Increases system voltage when the battery and BMS are approved for the planned series count.
Parallel connection: Increases available capacity and energy when branch protection and cable sizing are correct.
Mixed series-parallel banks: Require written confirmation of the model, BMS revision, connection limits and protection design.
How to Charge a 12V 100Ah LiFePO4 Battery
The battery uses a CC/CV charging profile with a reference charge voltage of 14.4V ± 0.2V and a recommended charging current of approximately 20A.
LiFePO4-compatible AC battery charger
Solar panel with a suitable MPPT charge controller
Alternator with a compatible DC-to-DC charger
Generator with a suitable inverter-charger
Do not connect an energy source directly to the battery. Avoid automatic equalization and uncontrolled desulfation settings intended for flooded lead-acid batteries.
12V 100Ah Group 24 LiFePO4 Battery Specifications
Parameter
Specification
Battery Chemistry
LiFePO4
Nominal Voltage
12.8V
Rated Capacity
100Ah
Energy
1,280Wh
Battery Format
Group 24
Dimensions
Approx. 10.24 × 6.61 × 8.27 in / 260 × 168 × 210 mm
Weight
Approx. 21.87 lb / 9.92 kg
Battery Management System
100A Smart BMS
Maximum Continuous Charge Current
100A
Maximum Continuous Discharge Current
100A
Maximum Continuous Output Power
1,280W
Recommended Charge Current
20A
Charge Voltage
14.4V ± 0.2V
Charge Method
CC/CV
Bluetooth Monitoring
Supported
Self-Heating
Not included
Low-Temperature Protection
Supported
Charge Temperature
0°C to 50°C / 32°F to 122°F
Discharge Temperature
−20°C to 60°C / −4°F to 140°F
Storage Temperature
−10°C to 50°C / 14°F to 122°F
Terminal Type
M8 bolts
Housing Material
ABS
Ingress Protection
IP65
12V 100Ah Group 24 Battery Technical Documents
Review the model-specific technical documentation for electrical ratings, dimensions, operating temperatures, Bluetooth functions and approved battery-bank configurations.
Can this Group 24 LiFePO4 battery replace an AGM battery?
Yes, for compatible 12V house-power applications after confirming physical fit, charging profile, terminal layout, current demand, cable size and fuse protection.
Is this 12V 100Ah lithium battery suitable for RV use?
Yes. It is suitable for compatible RV, motorhome, travel-trailer and camper-van house-power systems.
Does Bluetooth battery monitoring require internet access?
Standard Bluetooth monitoring connects locally to a compatible mobile device and does not normally require internet access for basic battery monitoring.
Can this LiFePO4 battery charge below freezing?
The BMS pauses charging below approximately 0°C / 32°F and restores charging after the cells return to a safe temperature. This model does not include self-heating.
Can this 12V battery be charged from solar or an alternator?
Yes, with a suitable lithium-compatible MPPT controller. Alternator charging may require a properly sized DC-to-DC charger.
Can Group 24 LiFePO4 batteries be connected in series or parallel?
Yes, when the ordered BMS configuration and product manual support the planned connection. Use identical batteries with matched state of charge and suitable overcurrent protection.
Is this battery suitable for engine starting?
No. It is a deep-cycle energy-storage battery for compatible house-power and auxiliary systems. Do not use it as an automotive or marine engine-starting battery.
Need Help Choosing the Right Group 24 Battery?
Contact us for product specifications, system compatibility, volume pricing or OEM battery requirements. Our team can help confirm the correct battery configuration for your RV, marine or off-grid application.
We manufacture and test LiFePO4 battery cells and packs in-house. Our 300+ employee factory supports OEM and ODM projects, with UL, CE, UN38.3, IEC 62619, RoHS and MSDS documentation available for selected models.
Answers about lead-acid replacement, system compatibility, OEM battery development, certifications and wholesale orders.
Can LiFePO4 batteries replace lead-acid batteries?
Many LiFePO4 batteries can replace compatible lead-acid deep-cycle batteries in RVs, boats, golf carts and industrial equipment. Before installation, confirm the system voltage, battery dimensions, terminal layout, charger profile, maximum load, cable size, fuse rating and operating temperature.
Are LiFePO4 batteries compatible with existing chargers and inverters?
Most LiFePO4 batteries are compatible with standard 12V, 24V, 36V or 48V inverters when the system voltage and power requirements match. Many modern chargers also include a LiFePO4 charging profile. For lead-acid replacement projects, confirm the charger voltage, inverter rating and maximum load before installation. A compatible charger or DC-to-DC charger may be required if the existing charging equipment does not support LiFePO4 batteries.
Can you provide custom or OEM LiFePO4 batteries?
Yes. OEM and custom battery support can include voltage, capacity, BMS settings, enclosures, terminals, connectors, communication protocols, labels and packaging. Send us the application, electrical requirements, installation dimensions and expected order quantity for review.
What is the minimum order quantity for wholesale or OEM orders?
MOQ depends on the battery model, specification and customization requirements. Standard models may be available for sample testing, while custom enclosures, private labels and OEM production normally require a confirmed order quantity. Contact us with the model and required quantity for details.
What certifications and battery documents are available?
Available certifications and documents depend on the battery model and destination market. Supporting documents may include UN38.3, MSDS, CE, RoHS and product test reports. Confirm the required documents and target market before placing an order.
What are the production lead time and shipping options?
Lead time depends on the battery model, order quantity, customization and testing requirements. Export shipping options are arranged according to the battery specification, destination and order volume. Send us the required quantity, delivery location and target schedule for a project-specific quotation.